View BA2904SFVM-TR_8432079.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

datashee t www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 1/52 23.jan.2014 rev.003 tsz22111 ? 14 ? 001 maximum operating temperature output current source/sink input offset voltage operational amplifiers ground sense operational amplifiers ba10358xx, ba10324axx, ba2 904xxx, ba2904sxxx, ba2904wxx ba2902xx, ba2902sxx general description general purpose ba10358 / ba10324a and high reliability ba2904 / ba2902 integrate two or four independent op-amps on a single chip and have some features of high-gain, lo w power consumption, and wide operating voltage range of 3v to 36v (single power supply ). ba2904w have low input offset voltage(2mv max.). features ? operable with a single power supply ? wide operating supply voltage range ? input and output are operable gnd sense ? low supply current ? high open loop voltage gain ? wide temperature range application ? current sense application ? buffer application amplifier ? active filter ? consumer electronics key specification ? wide operating supply voltage (single supply): ba10358/ba10324a +3.0v to +32.0v ba2904/ba2902 +3.0v to +36.0v ? wide temperature range: ba10358/ ba10324a -40c~+85c ba2904s/ ba2902s -40c~+105c ba2904/ ba2902 -40c~+125c ba2904w -40c~+125c ? input offset voltage: ba10358/ ba10324a 7mv (max) ba2904s/ ba2902s 7mv (max) ba2904/ ba2902 7mv (max) ba2904w 2mv (max) ? low input bias current: ba10358 45na (typ) ba10324a 20na (typ) ba2904s/ ba2902s 20na (typ) ba2904/ ba2902 20na (typ) ba2904w 20na (typ) packages w(typ) x d(typ) x h(max) sop8 5.00mm x 6.20mm x 1.71mm sop-j8 4.90mm x 6.00mm x 1.65mm ssop-b8 3.00mm x 6.40mm x 1.35mm msop8 2.90mm x 4.00mm x 0.90mm sop14 8.70mm x 6.20mm x 1.71mm sop-j14 8.65 mm x 6.00mm x 1.65mm ssop-b14 5.00 mm x 6.40mm x 1.35mm selection guide product structure silicon monolithic integrated circuit this product is not designed prot ection against radioactive rays. normal high-reliability dual quad dual quad +85c +105c +125c ba10358f ba10358fv ba10358fj ba10324af ba10324afv ba10324afj ba2904sf ba2904sfv ba2904sfvm ba2904f ba2904fv ba2904fvm ba2902sf ba2902sfv ba2902f ba2902fv 30ma/20ma 30ma/20ma 35ma/20ma 20ma/20ma 7mv 7mv 7mv 7mv 2mv ba2904wf ba2904wfv downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 2/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx c - + c + - - + ee - + cc simplified schematic pin configuration ba10358f,ba2904sf,ba2904f,ba2904wf :sop8 ba10358fv,ba2904sfv,ba2904fv,ba2904wfv :ssop-b8 ba2904sfvm,ba2904fvm :msop8 ba10358fj :sop-j8 pin no. pin name 1 out1 2 -in1 3 +in1 4 vee 5 +in2 6 -in2 7 out2 8 vcc ba10324af,ba2902sf,ba2902f :sop14 ba10324afv,ba2902sfv,ba2902fv :ssop-b14 ba10324afj :sop-j14 pin no. pin name 1 out1 2 -in1 3 +in1 4 vcc 5 +in2 6 -in2 7 out2 8 out3 9 -in3 10 +in3 11 vee 12 +in4 13 -in4 14 out4 figure 1. simplified schematic one channel only in in out vcc vee c + - c - + - + cc + - ee c - + + - c - + + - downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 3/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx package sop8 ssop-b8 msop8 sop-j8 sop14 ssop-b14 sop-j14 ba10358f ba2904sf ba2904f ba2904wf ba10358fv ba2904sfv ba2904fv ba2904wfv ba2904sfvm ba2904fvm ba10358fj ba10324af ba2902sf ba2902f ba10324afv ba2902sfv ba2902fv ba10324afj ordering information b a x x x x x x x x - x x part number. ba10358xx ba10324axx ba2904xxx ba2904sxxx ba2904wxx ba2902xx ba2902sxx package f : sop8 sop14 fv : ssop-b8 ssop-b14 fvm : msop8 fj : sop-j8 sop-j14 packaging and forming specification e2: embossed tape and reel (sop8/sop14/ssop-b8/ ssop-b14/sop-j8/sop-j14) tr: embossed tape and reel (msop8) line-up topr input offset voltage (max) supply current (typ) package orderable part number -40c to +85c 7mv 0.5ma sop8 reel of 2500 ba10358f-e2 sop-j8 reel of 2500 ba10358fj-e2 ssop-b8 reel of 2500 ba10358fv-e2 0.6ma sop14 reel of 2500 ba10324af-e2 sop-j14 reel of 2500 ba10324afj-e2 ssop-b14 reel of 2500 ba10324afv-e2 -40c to +105c 0.5ma sop8 reel of 2500 ba2904sf-e2 ssop-b8 reel of 2500 ba2904sfv-e2 msop8 reel of 3000 BA2904SFVM-TR 0.7ma sop14 reel of 2500 ba2902sf-e2 ssop-b14 reel of 2500 ba2902sfv-e2 -40c to +125c 0.5ma sop8 reel of 2500 ba2904f-e2 ssop-b8 reel of 2500 ba2904fv-e2 msop8 reel of 3000 ba2904fvm-tr 0.7ma sop14 reel of 2500 ba2902f-e2 ssop-b14 reel of 2500 ba2902fv-e2 2mv 0.5ma sop8 reel of 2500 ba2904wf-e2 ssop-b8 reel of 2500 ba2904wfv-e2 downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 4/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx absolute maximum ratings (t a =25c) ba10358, ba10324a parameter symbol ratings unit supply voltage vcc-vee +32 v power dissipation p d sop8 620 (note 1,7) mw sop-j8 540 (note 2,7) ssop-b8 500 (note 3,7) sop14 450 (note 4,7) sop-j14 820 (note 5,7) ssop-b14 700 (note 6,7) differential input voltage (note 8) v id +32 v input common-mode voltage range v icm (vee-0.3) to (vee+32) v input current (note 9) i i -10 ma wide operating supply voltage v opr +3.0 to +32.0 v operating temperature range t opr -40 to +85 c storage temperature range t stg -55 to +125 c maximum junction temperature t jmax +125 c note: absolute maximum rating item indicates the condition which must not be exceeded. application if voltage in excess of abso lute maximum rating or use out of absolute maximum rated temperature en vironment may cause deterior ation of characteristics. (note 1) to use at temperature above t a =25c reduce 6.2mw. (note 2) to use at temperature above t a =25c reduce 5.4mw (note 3) to use at temperature above t a =25c reduce 5.0mw. (note 4) to use at temperature above t a =25c reduce 4.5mw. (note 5) to use at temperature above t a =25c reduce 8.2mw (note 6) to use at temperature above t a =25c reduce 7.0mw. (note 7) mounted on a fr4 glass epoxy pcb 70mm70mm1.6mm (copper foil area less than 3%). (note 8) the voltage difference between inverting input and non-inverting input is the differential input voltage. then input terminal voltage is set to more than vee. (note 9) an excessive input current will flow when input voltages of less than vee-0.6v are applied. the input current can be set to less than the rated current by adding a limiting resistor. caution: operating the ic over the absolute ma ximum ratings may damage the ic. the damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. ther efore, it is important to consider circuit protection measures, such as adding a f use, in case the ic is operated over the absolute maximum ratings. downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 5/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx absolute maximum ratings (t a =25c) ba2904, ba2902 parameter symbol ratings unit ba2904s ba2902s ba2904, ba2904w ba2902 supply voltage vcc-vee +36 v power dissipation p d sop8 775 (note 10,15) mw ssop-b8 625 (note 11,15) msop8 600 (note 12,15) sop14 560 (note 13,15) ssop-b14 870 (note 14,15) differential input voltage (note 16) v id +36 v input common-mode voltage range v icm (vee-0.3) to (vee+36) v input current (note 17) i i -10 ma wide operating supply voltage v opr +3.0 to +36.0 v operating temperature range t opr -40 to +105 -40 to +125 c storage temperature range t stg -55 to +150 c maximum junction temperature t jmax +150 c (note 10) to use at temperature above t a =25c reduce 6.2mw. (note 11) to use at temperature above t a =25c reduce 5.0mw. (note 12) to use at temperature above t a =25c reduce 4.8mw. (note 13) to use at temperature above t a =25c reduce 4.5mw. (note 14) to use at temperature above t a =25c reduce 7.0mw. (note 15) mounted on a fr4 glass epoxy pcb 70mm70mm1.6mm (copper foil area less than 3%). (note 16) the voltage difference between inverting input and non-inverting input is the di fferential input voltage. then input terminal voltage is set to more than vee. (note 17) an excessive input current will flow when input voltages of less than vee-0.6v are applied. the input current can be set to le ss than the rated current by adding a limiting resistor. caution: operating the ic over the absolute maximum ratings may damage the ic. the damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. therefore, it is important to consider circuit protection measures, such as adding a f use, in case the ic is operated over the absolute maximum ratings. downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 6/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx electrical characteristics ba10358 (unless otherwise specified vcc=+5v, vee=0v, t a =25c) parameter symbol limits unit condition min. typ. max. input offset voltage (note 18) v io - 2 7 mv out=1.4v input offset current (note 18) i io - 5 50 na out=1.4v input bias current (note 19) i b - 45 250 na out=1.4v supply current i cc - 0.5 1.2 ma rl= , all op-amps maximum output voltage(high) v oh 3.5 - - v rl= 2k ? maximum output voltage(low) v ol - - 250 mv rl= , all op-amps large signal voltage gain a v 25 100 - v/mv rl R 2k ? , vcc=15v out=1.4 to 11.4v 88 100 - db input common-mode voltage range v icm 0 - vcc-1.5 v (vcc-vee)=5v out=vee+1.4v common-mode rejection ratio cmrr 65 80 - db out=1.4v power supply rejection ratio psrr 65 100 - db vcc=5 to 30v output source current i source 10 20 - ma vin+=1v, vin-=0v out=0v, 1ch is short circuit output sink current i sink 10 20 - ma vin+=0v, vin-=1v out=5v, 1ch is short circuit channel separation cs - 120 - db f=1khz, input referred slew rate sr - 0.2 - v/ s vcc=15v, av=0db rl=2k ? , cl=100pf gain band width gbw - 0.5 - mhz vcc=30v, rl=2k ? cl=100pf (note 18) absolute value (note 19) current direction: since first input stage is composed with pnp transistor, input bi as current flows out of ic. downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 7/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx ba10324a (unless otherwise specified vcc=+5v, vee=0v, t a =25c) parameter symbol limits unit condition min. typ. max. input offset voltage (note 20) v io - 2 7 mv out=1.4v input offset current (note 20) i io - 5 50 na out=1.4v input bias current (note 21) i b - 20 250 na out=1.4v supply current i cc - 0.6 2 ma rl= , all op-amps maximum output voltage(high) v oh 3.5 - - v rl= 2k ? maximum output voltage(low) v ol - - 250 mv rl= , all op-amps large signal voltage gain a v 25 100 - v/mv rl R 2k ? , vcc=15v out=1.4 to 11.4v 88 100 - db input common-mode voltage range v icm 0 - vcc-1.5 v (vcc-vee)=5v out=vee+1.4v common-mode rejection ratio cmrr 65 75 - db out=1.4v power supply rejection ratio psrr 65 100 - db vcc=5 to 30v output source current i source 20 35 - ma vin+=1v, vin-=0v out=0v, 1ch is short circuit output sink current i sink 10 20 - ma vin+=0v, vin-=1v out=5v, 1ch is short circuit channel separation cs - 120 - db f=1khz, input referred slew rate sr - 0.2 - v/ s vcc=15v, av=0db rl=2k ? , cl=100pf gain band width gbw - 0.5 - mhz vcc=30v, rl=2k ? cl=100pf (note 20) absolute value (note 21) current direction: since first input stage is composed with pnp transistor, input bi as current flows out of ic. downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 8/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx ba2904, ba2904s (unless otherwi se specified vcc=+5v, vee=0v) parameter symbol temperature range limits unit condition min. typ. max. input offset voltage (note 22,23) v io 25c - 2 7 mv out=1.4v full range - - 10 vcc=5 to 30v, out=1.4v input offset voltage drift v io / t - - 7 - v/c out=1.4v input offset current (note 22,23) i io 25c - 2 50 na out=1.4v full range - - 200 input offset current drift i io / t - - 10 - pa/c out=1.4v input bias current (note 22,23) i b 25c - 20 250 na out=1.4v full range - - 250 supply current (note 23) i cc 25c - 0.5 1.2 ma rl= , all op-amps full range - - 2 maximum output voltage(high) (note 23) v oh 25c 3.5 - - v rl=2k ? full range 27 28 - vcc=30v, rl=10k ? maximum output voltage(low) (note 23) v ol full range - 5 20 mv rl= , all op-amps large signal voltage gain a v 25c 25 100 - v/mv rl R 2k ? , vcc=15v out=1.4 to 11.4v 88 100 - db input common-mode voltage range v icm 25c 0 - vcc-1.5 v (vcc-vee)=5v out=vee+1.4v common-mode rejection ratio cmrr 25c 50 80 - db out=1.4v power supply rejection ratio psrr 25c 65 100 - db vcc=5 to 30v output source current (note 23,24) i source 25c 20 30 - ma vin+=1v, vin-=0v out=0v, 1ch is short circuit full range 10 - - output sink current (note 23,24) i sink 25c 10 20 - ma vin+=0v, vin-=1v out=5v, 1ch is short circuit full range 2 - - 25c 12 40 - a vin+=0v, vin-=1v out=200mv channel separation cs 25c - 120 - db f=1khz, input referred slew rate sr 25c - 0.2 - v/ s vcc=15v, av=0db rl=2k ? , cl=100pf gain band width gbw 25c - 0.5 - mhz vcc=30v, rl=2k ? cl=100pf input referred noise voltage v n 25c - 40 - hz nv/ vcc=15v, vee=-15v rs=100 ? , vi=0v, f=1khz (note 22) absolute value (note 23) ba2904s :full range -40 to +105c ba2904 :full range -40 to +125c (note 24) under high temperatures, please consider th e power dissipation when selecting the output current. when the output terminal is continuously shorted the outp ut current reduces the internal temperature by flushing. downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 9/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx ba2904w (unless otherwise specified vcc=+5v, vee=0v) parameter symbol temperature range limits unit condition min. typ. max. input offset voltage (note 25) v io 25c - 0.5 2 mv out=1.4v input offset voltage drift v io / t - - 7 - v/c out=1.4v input offset current (note 25) i io 25c - 2 50 na out=1.4v input offset current drift i io / t - - 10 - pa/c out=1.4v input bias current (note 25) i b 25c - 20 250 na out=1.4v full range - - 250 supply current i cc 25c - 0.5 1.2 ma rl= , all op-amps full range - - 1.2 maximum output voltage(high) v oh 25c 3.5 - - v rl=2k ? full range 27 28 - vcc=30v, rl=10k ? maximum output voltage(low) v ol full range - 5 20 mv rl= , all op-amps large signal voltage gain a v 25c 25 100 - v/mv rl R 2k ? , vcc=15v out=1.4 to 11.4v 88 100 - db input common-mode voltage range v icm 25c 0 - vcc-1.5 v (vcc-vee)=5v out=vee+1.4v common-mode rejection ratio cmrr 25c 50 80 - db out=1.4v power supply rejection ratio psrr 25c 65 100 - db vcc=5 to 30v output source current (note 26) i source 25c 20 30 - ma vin+=1v, vin-=0v out=0v, 1ch is short circuit full range 10 - - output sink current (note 26) i sink 25c 10 20 - ma vin+=0v, vin-=1v out=5v, 1ch is short circuit full range 2 - - 25c 12 40 - a vin+=0v, vin-=1v out=200mv channel separation cs 25c - 120 - db f=1khz, input referred slew rate sr 25c - 0.2 - v/ s vcc=15v, av=0db rl=2k ? , cl=100pf gain band width gbw 25c - 0.5 - mhz vcc=30v, rl=2k ? cl=100pf input referred noise voltage v n 25c - 40 - hz nv/ vcc=15v, vee=-15v rs=100 ? , vi=0v, f=1khz (note 25) absolute value (note 26) under high temperatures, please consider the power dissipation when selecting the output current. when the output terminal is continuously shorted the outp ut current reduces the internal temperature by flushing. downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 10/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx ba2902, ba2902s (unless otherwi se specified vcc=+5v, vee=0v) parameter symbol temperature range limits unit condition min. typ. max. input offset voltage (note 27,28) v io 25c - 2 7 mv out=1.4v full range - - 10 vcc=5 to 30v, out=1.4v input offset voltage drift v io / t - - 7 - v/c out=1.4v input offset current (note 27,28) i io 25c - 2 50 na out=1.4v full range - - 200 input offset current drift i io / t - - 10 - pa/c out=1.4v input bias current (note 27,28) i b 25c - 20 250 na out=1.4v full range - - 250 supply current (note 28) i cc 25c - 0.7 2 a rl= , all op-amps full range - - 3 maximum output voltage(high) (note 28) v oh 25c 3.5 - - v rl=2k ? full range 27 28 - vcc=30v, rl=10k ? maximum output voltage(low) (note 28) v ol full range - 5 20 mv rl= , all op-amps large signal voltage gain a v 25c 25 100 - v/mv rl R 2k ? , vcc=15v out=1.4 to 11.4v 88 100 - db input common-mode voltage range v icm 25c 0 - vcc-1.5 v (vcc-vee)=5v out=vee+1.4v common-mode rejection ratio cmrr 25c 50 80 - db out=1.4v power supply rejection ratio psrr 25c 65 100 - db vcc=5 to 30v output source current (note 28,29) i source 25c 20 30 - ma vin+=1v, vin-=0v out=0v 1ch is short circuit full range 10 - - output sink current (note 28,29) i sink 25c 10 20 - ma vin+=0v, vin-=1v out=5v, 1ch is short circuit full range 2 - - 25c 12 40 - a vin+=0v, vin-=1v out=200mv channel separation cs 25c - 120 - db f=1khz, input referred slew rate sr 25c - 0.2 - v/ s vcc=15v, av=0db rl=2k ? , cl=100pf gain band width gbw 25c - 0.5 - mhz vcc=30v, rl=2k ? cl=100p input referred noise voltage v n 25c - 40 - hz nv/ vcc=15v, vee=-15v rs=100 ? , vi=0v, f=1khz (note 27) absolute value (note 28) ba2902s :full range -40 to +105c ,ba2902 :full range -40 to +125c (note 29) under high temperatures, please consider th e power dissipation when selecting the output current. when the output terminal is continuously shorted the outp ut current reduces the internal temperature by flushing. downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 11/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx description of electri cal characteristics described below are descriptions of the rele vant electrical terms used in this datasheet. items and symbols used are also shown. note that item name and symbol and their meaning ma y differ from those on another manufacturers document or general document. 1. absolute maximum ratings absolute maximum rating items indicate the condition which must not be exceeded. application of voltage in excess of absolute maximum rating or use out of absolute maximum rated temperature environment may cau se deterioration of characteristics. (1) supply voltage (vcc/vee) indicates the maximum voltage that can be applied between the positive power supply terminal and negative power supply terminal without deterioration or destruct ion of characteristics of internal circuit. (2) differential input voltage (v id ) indicates the maximum voltage that can be applied betw een non-inverting and inverting terminals without damaging the ic. (3) input common-mode voltage range (v icm ) indicates the maximum voltage that can be applied to the non-inverting and inverting terminals without deterioration or destruction of electrical characteristics. input common-mode voltage range of the maximum ratin gs does not assure normal operation of ic. for normal operation, use the ic within the input co mmon-mode voltage range characteristics. (4) power dissipation (p d ) indicates the power that can be consumed by the ic when mounted on a specific board at the ambient temperature 25 (normal temperature). as for package product, pd is determi ned by the temperature that can be permitted by the ic in the package (maximum junction temperature) and the thermal resistance of the package. 2. electrical characteristics (1) input offset voltage (v io ) indicates the voltage difference between non-inverting termi nal and inverting terminals. it can be translated into the input voltage difference required for setting the output voltage at 0 v. (2) input offset voltage drift ( v io / t) denotes the ratio of the input offset voltage fluc tuation to the ambient te mperature fluctuation. (3) input offset current (i io ) indicates the difference of input bias current bet ween the non-inverting and inverting terminals. (4) input offset current drift ( iio/ t) signifies the ratio of the input offset current fl uctuation to the ambient temperature fluctuation. (4) input bias current (i b ) indicates the current that flows into or out of the input terminal. it is defined by the average of input bias currents at the non-inverting and inverting terminals. (5) supply current (icc) indicates the current that flows within the ic under specified no-load conditions. (7) maximum output voltage(high) / maxi mum output voltage(low) (voh/vol) indicates the voltage range of the outpu t under specified load condition. it is typically divided into maximum output voltage high and low. maximum output voltage high indica tes the upper limit of out put voltage. maximum output voltage low indicates the lower limit. (8) large signal voltage gain (av) indicates the amplifying rate (gain) of output voltage against the voltage difference between non-inverting terminal and inverting terminal. it is normally the amplifying rate (gain) with reference to dc voltage. av = (output voltage) / (differential input voltage) (9) input common-mode voltage range (v icm ) indicates the input voltage range where ic normally operates. (10) common-mode rejection ratio (cmrr) indicates the ratio of fluctuation of input offset voltage when the input common mode voltage is changed. it is normally the fluctuation of dc. cmrr = (change of input common-mode voltage)/(input offset fluctuation) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 12/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx (11) power supply rejection ratio (psrr) indicates the ratio of fluctuation of input offset voltage when supply voltage is changed. it is normally the fluctuation of dc. psrr= (change of power supply volta ge)/(input offset fluctuation) (12) output source current/ output sink current (i source / i sink ) the maximum current that c an be output from the ic under specific output conditions. the output source current indicates the current flowing out from the ic, and the output sink current indica tes the current flowing into the ic. indicates the current flowing out from the ic, and the output sink current indica tes the current flowing into the ic. (13) channel separation (cs) indicates the fluctuation in the output vo ltage of the driven channel with reference to the change of output voltage of the channel which is not driven. (14) slew rate (sr) indicates the ratio of the change in output voltage wi th time when a step input signal is applied. (15) gain bandwidth (gbw) the product of the open-loop voltage gai n and the frequency at which the voltage gain decreases 6db/octave. (16) input referred noise voltage (v n ) indicates a noise voltage generated inside the operational amplifier equivalent by ideal voltage source connected in series with input terminal. downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 13/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx 0.0 0.2 0.4 0.6 0.8 1.0 -50 -25 0 25 50 75 100 supply current [ma] ambient temperature [ ] 0.0 0.2 0.4 0.6 0.8 1.0 0 5 10 15 20 25 30 35 supply current [ma] supply voltage [v] 0 5 10 15 20 25 30 35 0 5 10 15 20 25 30 35 maximum output voltage [v] supply voltage [v] typical performance curves ba10358 (*) the above data is measurement value of typical sample, it is not guaranteed. 0 200 400 600 800 1000 0 25 50 75 100 125 ambient temperature [ ] . power dissipation [mw] . ba10358f ba10358f v 85 ba10358fj 32 v 3 v 5 v 85 25 -40 85 25 -40 figure 2. derating curve figure 3. su pp l y current C su pp l y volta g e figure 4. supply current C ambient temperature figure 5. maximum output voltage - supply voltage ( rl=10k ? ) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 14/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx 0 1 2 3 4 5 - 5 0- 2 5 0 2 55 07 51 0 0 maximum output voltage [v] ambient temperature [ ] 0 10 20 30 40 012345 output source current [ma] output voltage [v] 0 10 20 30 40 - 5 0- 2 5 0 2 55 07 51 0 0 output source current [ma] ambient temperature [ ] 0. 00 1 0. 01 0. 1 1 10 10 0 00 . 40 . 81 . 21 . 62 output sink current [ma] output voltage [v] ba10358 (*) the above data is measurement value of typical sample, it is not guaranteed. 3v 5v 15v 85 25 -40 85 25 -40 figure 6. maximum output voltage - ambient temperature (vcc=5v, rl=2k ? ) figure 9. output sink current - output voltage ( vcc=5v ) figure 7. output source current - output voltage ( vcc=5v ) figure 8. output source current - ambient temperature (out=0v) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 15/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx 0 10 20 30 40 -50 -25 0 25 50 75 100 output sink current [ma] ambient temperature [ ] 0 10 20 30 40 50 60 0 5 10 15 20 25 30 35 low-level sink current [ a] supply voltage [v] 0 10 20 30 40 50 60 - 5 0- 2 5 0 2 55 07 51 0 0 low-level sink current [ a] ambient temperature [ ] -8 -6 -4 -2 0 2 4 6 8 0 5 10 15 20 25 30 35 input offset voltage [mv] supply voltage [v] ba10358 (*) the above data is measurement value of typical sample, it is not guaranteed. 15v 3v 5 v 85 25 -40 32v 3v 5v 85 25 -40 figure 11. low level sink current - supply voltage (out=0.2v) figure 12. low level sink current - ambient temperature (out=0.2v) figure 13. input offset voltage - supply voltage (v icm =0v, out=1.4v) figure 10. output sink current - ambient temperature (out=vcc) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 16/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx -8 -6 -4 -2 0 2 4 6 8 -50 -25 0 25 50 75 100 input offset voltage [mv] ambient temperature [ ] 0 10 20 30 40 50 0 5 10 15 20 25 30 35 input bias current [na] supply voltage [v] 0 10 20 30 40 50 - 5 0- 2 5 0 2 55 07 51 0 0 input bias current [na] ambient temperature [ ] -10 0 10 20 30 40 50 - 5 0- 2 5 0 2 55 07 51 0 0 input bias current [na] ambient temperature [ ] ba10358 (*) the above data is measurement value of typical sample, it is not guaranteed. 32v 5v 3v 32 v 3v 5 v 85 25 -40 figure 16. input bias current - ambient temperature (v icm =0v, out=1.4v) figure 14. input offset voltage - ambient temperature (v icm =0v, out=1.4v) figure 15. input bias current - supply voltage (v icm =0v, out=1.4v) figure 17. input bias current - ambient temperature ( vcc=30v , v icm =28v , out=1.4v ) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 17/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx -8 -6 -4 -2 0 2 4 6 8 - 1012345 input offset voltage [mv] . input voltage [v] -10 -5 0 5 10 0 5 10 15 20 25 30 35 input offset current [na] supply voltage [v] -10 -5 0 5 10 - 5 0- 2 5 0 2 55 07 51 0 0 input offset current [na] ambient temperature [ ] 60 70 80 90 100 110 120 130 140 4 6 8 1 01 21 41 6 large signal voltage gain [db] supply voltage [v] ba10358 (*) the above data is measurement value of typical sample, it is not guaranteed. 85 25 -40 85 25 -40 32v 5v 3v 85 25 -40 figure 21. large signal voltage gain - supply voltage (rl=2k ? ) figure 20. input offset current - ambient temperature (v icm =0v, out=1.4v) figure 19. input offset current - supply voltage (v icm =0v, out=1.4v) figure 18. input offset voltage - common mode input voltage (vcc=5v) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 18/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx 60 70 80 90 10 0 11 0 12 0 13 0 14 0 -50 -25 0 25 50 75 100 large signal voltage gain [db] ambient temperature [ ] 40 60 80 10 0 12 0 14 0 0 5 10 15 20 25 30 35 common mode rejection ratio [db] supply voltage [v] 40 60 80 10 0 12 0 14 0 - 5 0- 2 50 2 55 07 51 0 0 common mode rejection ratio [db] ambient temperature [ ] 60 70 80 90 10 0 11 0 12 0 13 0 14 0 -50 -25 0 25 50 75 100 power supply rejection ratio [db] ambient temperature [ ] ba10358 (*) the above data is measurement value of typical sample, it is not guaranteed. 15v 5v 85 25 -40 32 v 3v 5 v figure 24. common mode rejection ratio - ambient temperature figure 22. large signal voltage gain - ambient temperature (rl=2k ? ) figure 23. common mode rejection ratio - supply voltage figure 25. power supply rejection ratio - ambient temperature downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 19/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx 0. 0 0. 4 0. 8 1. 2 1. 6 2. 0 0 5 10 15 20 25 30 35 supply current [ma] supply voltage [v] 0. 0 0. 4 0. 8 1. 2 1. 6 2. 0 -50 -25 0 25 50 75 100 supply current [ma] ambient temperature [ ] 0 5 10 15 20 25 30 35 0 5 10 15 20 25 30 35 maximum output voltage [v] supply voltage [v] ba10324a (*) the above data is measurement value of typical sample, it is not guaranteed. 0 200 400 600 800 1000 0 25 50 75 100 125 ambient temperature [ ] . power dissipation [mw] . 85 ba10324afj ba10324af ba10324afv 85 25 -40 32v 3v 5 v 85 25 -40 figure 26. derating curve figure 27. supply current - supply voltage figure 29. maximum output voltage - supply voltage (rl=10k ? ) figure 28. supply current - ambient temperature downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 20/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx 0 1 2 3 4 5 - 5 0- 2 50 2 55 07 51 0 0 maximum output voltage [v] ambient temperature [ ] 0 10 20 30 40 50 012345 output source current [ma] output voltage [v] 0. 00 1 0. 01 0. 1 1 10 10 0 0 0.4 0.8 1.2 1.6 2 output sink current [ma] output voltage [v] 0 10 20 30 40 50 -50 -25 0 25 50 75 100 ou tpu t sou r ce c urr en t [ ma] ambient temperature [ ] ba10324a (*) the above data is measurement value of typical sample, it is not guaranteed. 85 25 -40 85 25 -40 figure 33. output sink current - output voltage (vcc=5v) figure 30. maximum output voltage - ambient temperature (vcc=5v, rl=2k ? ) figure 31. output source current - output voltage (vcc=5v) figure 32. output source current - ambient temperature (out=0v) 15 v 3v 5v downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 21/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx 0 10 20 30 40 - 5 0- 2 50 2 55 07 51 0 0 output sink current [ma] ambient temperature [ ] 0 10 20 30 40 50 60 -50 -25 0 25 50 75 100 low-level sink current [ a] ambient temperature [ ] -8 -6 -4 -2 0 2 4 6 8 0 5 10 15 20 25 30 35 input offset voltage [mv] supply voltage [v] 0 10 20 30 40 50 60 0 5 10 15 20 25 30 35 low-level sink current [ a] supply voltage [v] ba10324a (*) the above data is measurement value of typical sample, it is not guaranteed. 15v 3v 5v 32v 3v 5v 85 25 -40 figure 34. output sink current - ambient temperature (out=vcc) figure 35. low level sink current - supply voltage (out=0.2v) figure 36. low level sink current - ambient temperature (out=0.2v) figure 37. input offset voltage - supply voltage (v icm =0v, out=1.4v) 85 25 -40 downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 22/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx -8 -6 -4 -2 0 2 4 6 8 - 5 0- 2 50 2 55 07 51 0 0 input offset voltage [mv] ambient temperature [ ] 0 10 20 30 40 50 0 5 10 15 20 25 30 35 input bias current [na] supply voltage [v] 0 10 20 30 40 50 - 5 0- 2 50 2 55 07 51 0 0 input bias current [na] ambient temperature [ ] -10 0 10 20 30 40 50 -50 -25 0 25 50 75 100 input bias current [na] ambient temperature [ ] ba10324a (*) the above data is measurement value of typical sample, it is not guaranteed. 32v 5v 3 v 32 v 3 v 5v 85 25 -40 figure 38. input offset voltage - ambient temperature (v icm =0v, out=1.4v) figure 40. input bias current - ambient temperature (v icm =0v, out=1.4v) figure 39. input bias current - supply voltage (v icm =0v, out=1.4v) figure 41. input bias current - ambient temperature (vcc=30v, v icm =28v, out=1.4v) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 23/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx -10 -5 0 5 10 -50 -25 0 25 50 75 100 input offset current [na] ambient temperature [ ] -8 -6 -4 -2 0 2 4 6 8 - 1012345 input offset voltage [mv] input voltage [v] -10 -5 0 5 10 0 5 10 15 20 25 30 35 i n pu t of f set c u rrent [ na] supply voltage [v] 60 70 80 90 10 0 11 0 12 0 13 0 14 0 4 6 8 1 01 21 41 6 large signal voltage gain [db] supply voltage [v] ba10324a (*) the above data is measurement value of typical sample, it is not guaranteed. 5 v 32 v 3 v 85 25 -40 85 25 -40 85 25 -40 figure 44. input offset current - ambient temperature (v icm =0v, out=1.4v) figure 42. input offset voltage - common mode input voltage (vcc=5v) figure 43. input offset current - supply voltage (v icm =0v, out=1.4v) figure 45. large signal voltage gain - supply voltage (rl=2k ? ) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 24/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx 60 70 80 90 10 0 11 0 12 0 13 0 14 0 -50 -25 0 25 50 75 100 large signal voltage gain [db] ambient temperature [ ] 40 60 80 10 0 12 0 14 0 0 5 10 15 20 25 30 35 common mode rejection ratio [db] supply voltage [v] 40 60 80 10 0 12 0 14 0 -50 -25 0 25 50 75 100 common mode rejection ratio [db] ambient temperature [ ] 60 70 80 90 10 0 11 0 12 0 13 0 14 0 -50 -25 0 25 50 75 100 power supply rejection ratio [db] ambient temperature [ ] ba10324a (*) the above data is measurement value of typical sample, it is not guaranteed. 15 v 5 v 85 25 -40 5v 32 v 3v figure 46. large signal voltage gain - ambient temperature (rl=2k ? ) figure 47. common mode rejection ratio - supply voltage figure 48. common mode rejection ratio - ambient temperature figure 49. power supply rejection ratio - ambient temperature downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 25/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx 0. 0 0. 2 0. 4 0. 6 0. 8 1. 0 0 1 02 03 04 0 supply current [ma] supply voltage [v] 0. 0 0. 2 0. 4 0. 6 0. 8 1. 0 - 50 -25 0 25 50 75 10 0 12 5 15 0 supply current [ma] ambient temperature [ ] 0 10 20 30 40 0 1 02 03 04 0 maximum output voltage [v] supply voltage [v] ba2904, ba2904s, ba2904w (*) the above data is measurement value of typical sample, it is not guaranteed. ba2904, ba2904w -40c to 125c ba2904s -40c to 105c 36 v 5 v 3 v 0 200 400 600 800 1000 0 25 50 75 100 125 150 ambient temperature [ ] . power dissipation [mw] . ba2904f ba2904wf ba2904sf ba2904fv ba2904wfv ba2904sfv ba2904fvm ba2904sfvm 105 125 105 -40 25 125 105 -40 25 figure 50. derating curve figure 52. supply current C ambient temperature figure 51. supply current- supply voltage figure 53. maximum output voltage - supply voltage (rl=10k ? ) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 26/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx 0 1 2 3 4 5 - 50 - 25 0 25 50 75 10 0 12 5 15 0 maximum output voltage [v] ambient temperature [ ] 0 10 20 30 40 50 012345 output source current [ma] output voltage [v] 0 10 20 30 40 50 -50-250 255075100125150 output source current [ma] ambient temperature [ ] 0. 00 1 0. 01 0. 1 1 10 10 0 0 0.4 0.8 1.2 1.6 2 ou tpu t si n k c urr en t [ ma] output voltage [v] ba2904, ba2904s, ba2904w (*) the above data is measurement value of typical sample, it is not guaranteed. 125 105 -40 25 3 v 15v 5 v 125 105 -40 25 figure 54. maximum output voltage - ambient temperature (vcc=5v, rl=2k ? ) figure 55. output source current - output voltage (vcc=5v) figure 56. output source current - ambient temperature (out=0v) figure 57. output sink current - output voltage (vcc=5v) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 27/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx 0 10 20 30 -50-250 255075100125150 output sink current [ma] ambient temperature [ ] 0 10 20 30 40 50 60 70 80 0 5 10 15 20 25 30 35 40 low-level sink current [ a] supply voltage [v] 0 10 20 30 40 50 60 70 80 -50-250 255075100125150 low-level sink current [ a] ambient temperature [ ] -8 -6 -4 -2 0 2 4 6 8 0 5 10 15 20 25 30 35 40 input offset voltage [mv] supply voltage [v] ba2904, ba2904s, ba2904w (*) the above data is measurement value of typical sample, it is not guaranteed. 105 125 -40 25 3v 15v 5v 125 105 -40 25 36 v 5v 3v figure 59. low level sink current - supply voltage (out=0.2v) figure 61. input offset voltage - supply voltage (v icm =0v, out=1.4v) figure 58. output sink current - ambient temperature (out=vcc) figure 60. low level sink current - ambient temperature (out=0.2v) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 28/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx -8 -6 -4 -2 0 2 4 6 8 -50-250 255075100125150 input offset voltage [mv] ambient temperature [ ] 0 10 20 30 40 50 0 5 10 15 20 25 30 35 40 input bias current [na] supply voltage [v] 0 10 20 30 40 50 -50-250 255075100125150 input bias current [na] ambient temperature [ ] -10 0 10 20 30 40 50 -50-250 255075100125150 input bias current [na] ambient temperature [ ] ba2904, ba2904s, ba2904w (*) the above data is measurement value of typical sample, it is not guaranteed. -40 25 105 125 5v 3v 36v 36v 5 v 3 v figure 63. input bias current - supply voltage (v icm =0v, out=1.4v) figure 62. input offset voltage - ambient temperature (v icm =0v, out=1.4v) figure 64. input bias current - ambient temperature (v icm =0v, out=1.4v) figure 65. input bias current - ambient temperature (vcc=30v, v icm =28v, out=1.4v) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 29/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx -8 -6 -4 -2 0 2 4 6 8 - 1012345 input offset voltage [mv] input voltage [v] -10 -5 0 5 10 0 5 10 15 20 25 30 35 40 input offset current [na] supply voltage [v] -10 -5 0 5 10 -50-250 255075100125150 input offset current [na] ambient temperature [ ] 60 70 80 90 10 0 11 0 12 0 13 0 14 0 4 6 8 1 01 21 41 6 large signal voltage gain [db] supply voltage [v] ba2904, ba2904s, ba2904w (*) the above data is measurement value of typical sample, it is not guaranteed. 105 125 -40 25 125 105 -40 25 -40 25 105 125 36v 5v 3v figure 69. large signal voltage gain - supply voltage (rl=2k ? ) figure 66. input offset voltage - common mode input voltage (vcc=5v) figure 67. input offset current - supply voltage (v icm =0v, out=1.4v) figure 68. input offset current - ambient temperature (v icm =0v, out=1.4v) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 30/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx 60 70 80 90 10 0 11 0 12 0 13 0 14 0 -50-250 255075100125150 large signal voltage gain [db] ambient temperature [ ] 40 60 80 10 0 12 0 14 0 0 1 02 03 04 0 common mode rejection ratio [db] supply voltage [v] 40 60 80 10 0 12 0 14 0 -50-250 255075100125150 common mode rejection ratio [db] ambient temperature [ ] 60 70 80 90 10 0 11 0 12 0 13 0 14 0 -50 - 25 0 25 50 75 10 0 12 5 15 0 power supply rejection ratio [db] ambient temperature [ ] ba2904, ba2904s, ba2904w (*) the above data is measurement value of typical sample, it is not guaranteed. 15v 5v -40 25 105 125 36 v 5v 3 v figure 70. large signal voltage gain - ambient temperature (rl=2k ? ) figure 71. common mode rejection ratio - supply voltage figure 72. common mode rejection ratio - ambient temperature figure 73. power supply rejection ratio - ambient temperature downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 31/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx 0. 0 0. 4 0. 8 1. 2 1. 6 2. 0 0 1 02 03 04 0 supply current [ma] supply voltage [v] 0. 0 0. 4 0. 8 1. 2 1. 6 2. 0 -50-250 255075100125150 supply current [ma] ambient temperature [ ] 0 10 20 30 40 0 1 02 03 04 0 maximum output voltage [v] supply voltage [v] ba2902, ba2902s (*) the above data is measurement value of typical sample, it is not guaranteed. ba2902 -40c to 125c ba2902s -40c to 105c 0 200 400 600 800 1000 02 55 07 51 0 01 2 51 5 0 ambient temperature [ ] . power dissipation [mw] . 105 ba2902fv ba2902sfv ba2902f ba2902sf -40 25 105 125 36 v 5v 3v 125 105 -40 25 figure 74. derating curve figure 75. supply current - supply voltage figure 76. supply current - ambient temperature figure 77. maximum output voltage - supply voltage (rl=10k ? ) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 32/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx 0 1 2 3 4 5 - 50 - 25 0 25 50 75 10 0 12 5 15 0 maximum output voltage [v] ambient temperature [ ] 0 10 20 30 40 50 012345 output source current [ma] output voltage [v] 0 10 20 30 40 50 -50-250 255075100125150 output source current [ma] ambient temperature [ ] 0. 00 1 0. 01 0. 1 1 10 10 0 0 0.4 0.8 1.2 1.6 2 ou tpu t si n k c urr en t [ ma] output voltage [v] ba2902, ba2902s (*) the above data is measurement value of typical sample, it is not guaranteed. 125 105 -40 25 3 v 15v 5 v 125 105 -40 25 figure 78. maximum output voltage - ambient temperature (vcc=5v, rl=2k ? ) figure 79. output source current - output voltage (vcc=5v) figure 80. output source current - ambient temperature (out=0v) figure 81. output sink current - output voltage (vcc=5v) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 33/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx 0 10 20 30 -50-250 255075100125150 output sink current [ma] ambient temperature [ ] 0 10 20 30 40 50 60 70 80 0 5 10 15 20 25 30 35 40 low-level sink current [ a] supply voltage [v] 0 10 20 30 40 50 60 70 80 -50-250 255075100125150 low-level sink current [ a] ambient temperature [ ] -8 -6 -4 -2 0 2 4 6 8 0 5 10 15 20 25 30 35 40 input offset voltage [mv] supply voltage [v] ba2902, ba2902s (*) the above data is measurement value of typical sample, it is not guaranteed. 105 125 -40 25 3v 15v 5v 125 105 -40 25 36 v 5v 3v figure 85. input offset voltage - supply voltage (v icm =0v, out=1.4v) figure 84. low level sink current - ambient temperature (out=0.2v) figure 83. low level sink current - supply voltage (out=0.2v) figure 82. output sink current - ambient temperature (out=vcc) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 34/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx -8 -6 -4 -2 0 2 4 6 8 -50-250 255075100125150 input offset voltage [mv] ambient temperature [ ] 0 10 20 30 40 50 0 5 10 15 20 25 30 35 40 input bias current [na] supply voltage [v] 0 10 20 30 40 50 -50-250 255075100125150 input bias current [na] ambient temperature [ ] -10 0 10 20 30 40 50 -50-250 255075100125150 input bias current [na] ambient temperature [ ] ba2902, ba2902s (*) the above data is measurement value of typical sample, it is not guaranteed. -40 25 105 125 5v 3v 36v 36 v 5v 3 v figure 86. input offset voltage - ambient temperature (v icm =0v, out=1.4v) figure 87. input bias current - supply voltage (v icm =0v, out=1.4v) figure 88. input bias current - ambient temperature (v icm =0v, out=1.4v) figure 89. input bias current - ambient temperature (vcc=30v, v icm =28v, out=1.4v) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 35/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx -8 -6 -4 -2 0 2 4 6 8 - 1012345 input offset voltage [mv] input voltage [v] -10 -5 0 5 10 0 5 10 15 20 25 30 35 40 input offset current [na] supply voltage [v] -10 -5 0 5 10 -50-250 255075100125150 input offset current [na] ambient temperature [ ] 60 70 80 90 10 0 11 0 12 0 13 0 14 0 4 6 8 1 01 21 41 6 large signal voltage gain [db] supply voltage [v] ba2902, ba2902s (*) the above data is measurement value of typical sample, it is not guaranteed. 105 125 -40 25 125 105 -40 25 -40 25 105 125 36v 5v 3v figure 90. input offset voltage - common mode input voltage (vcc=5v) figure 91. input offset current - supply voltage (v icm =0v, out=1.4v) figure 92. input offset current - ambient temperature (v icm =0v, out=1.4v) figure 93. large signal voltage gain - supply voltage (rl=2k ? ) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 36/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx 60 70 80 90 10 0 11 0 12 0 13 0 14 0 -50-250 255075100125150 large signal voltage gain [db] ambient temperature [ ] 40 60 80 10 0 12 0 14 0 0 1 02 03 04 0 common mode rejection ratio [db] supply voltage [v] 40 60 80 10 0 12 0 14 0 -50-250 255075100125150 common mode rejection ratio [db] ambient temperature [ ] 60 70 80 90 10 0 11 0 12 0 13 0 14 0 -50 - 25 0 25 50 75 10 0 12 5 15 0 power supply rejection ratio [db] ambient temperature [ ] ba2902, ba2902s (*) the above data is measurement value of typical sample, it is not guaranteed. 15v 5v -40 25 105 125 36 v 5v 3v figure 94. large signal voltage gain - ambient temperature (rl=2k ? ) figure 95. common mode rejection ratio - supply voltage figure 96. common mode rejection ratio - ambient temperature figure 97. power supply rejection ratio - ambient temperature downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 37/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx application information null method condition for test circuit 1 vcc, vee, e k , v icm unit : v parameter vf s1 s2 s3 ba10358 ba10324a ba2904 ba2902 calculation vcc vee e k v icm vcc vee e k v icm input offset voltage v f1 on on off 5 0 -1.4 0 5 to 30 0 -1.4 0 1 input offset current v f2 off off off 5 0 -1.4 0 5 0 -1.4 0 2 input bias current v f3 off on off 5 0 -1.4 0 5 0 -1.4 0 3 v f4 on off large signal voltage gain v f5 on on on 15 0 -1.4 0 15 0 -1.4 0 4 v f6 15 0 -11.4 0 15 0 -11.4 0 common-mode rejection ratio (input common-mode voltage range) v f7 on on off 5 0 -1.4 0 5 0 -1.4 0 5 v f8 5 0 -1.4 3.5 5 0 -1.4 3.5 power supply rejection ratio v f9 on on off 5 0 -1.4 0 5 0 -1.4 0 6 v f10 30 0 -1.4 0 30 0 -1.4 0 -calculation- 1. input offset voltage (vio) 2. input offset current (iio) 3. input bias current (ib) 4. large signal voltage gain (av) 5. common-mode rejection ration (cmrr) 6. power supply rejection ratio (psrr) figure . 98 test circuit1 (one channel only) vcc rf=50k ri=10k rs=50 rl sw2 500k 500k 0.1f ek 15v dut vee 50k vicm sw1 ri=10k vo vf rs=50 1000pf 0.1f -15v null sw3 v io |v f1 | = 1+r f /r s [v] a v |v f5 -v f6 | = 10 (1+r f /r s ) [db] 20log = cmrr |v f8 -v f7 | 3.5 (1+r f /r s ) [db] 20log = i b |v f4 -v f3 | 2 r i (1+r f /r s ) [a] i io |v f2 -v f1 | r i (1+r f /r s ) [a] = = psrr |v f10 C v f9 | 25 (1+ r f /r s ) [db] 20log downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 38/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx vh vl input wave t input voltage vh vl t v output wave sr= v/ t t output voltage switch condition for test circuit 2 sw no. sw 1 sw 2 sw 3 sw 4 sw 5 sw 6 sw 7 sw 8 sw 9 sw 10 sw 11 sw 12 sw 13 sw 14 supply current off off off on off on off off off off off off off off maximum output voltage(high) off off on off off on off off on off off off on off maximum output voltage(low) off off on off off on off off off off off off on off output source current off off on off off on off off off off off off off on output sink current off off on off off on off off off off off off off on slew rate off off off on off off off on on on off off off off gain bandwidth product off on off off on on off off on on off off off off equivalent input noise voltage on off off off on on off off off off on off off off figure 99. test circuit 2 (each op-amp) figure 100. slew rate input waveform figure 101. test circuit 3(channel separation) (r1=1k ? ,r2=100k ? ) 90% 10% vcc vee r1 v r 2 r 1/ / r2 out 1 =0. 5 vrms vin vcc vee r1 v r2 r1 // r2 out 2 other ch cs 20 log 100 out 1 out 2 sw4 sw2 sw3 sw10 sw11 sw12 sw9 sw6 sw7 sw8 c l sw13 sw5 r1 c r2 r l vee vcc v in- v in+ sw14 out sw1 r s downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 39/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx examples of circuit voltage follower inverting amplifier non-inverting amplifier voltage gain is 0 db. this circuit controls output voltage (out) equal input voltage (in), and keeps out with stable because of high input impedance and low output impedance. out is shown next formula. out=in for inverting amplifier, in is amplified by voltage gain decided r1 and r2, and phase reversed voltage is output. out is shown next formula. out=-(r2/r1) ? in input impedance is r1. for non-inverting amplifier, in is amplified by voltage gain decided r1 and r2, and phase is same with in. out is shown next formula. out= (1+r2/r1) ? in this circuit realizes high input impedance because input impedance is operat ional amplifiers input impedance. vee out in vcc r2 r1 vee r1//r2 in out vcc downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 40/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx figure 102. thermal resistance and derating power dissipation power dissipation (total loss) indicates the power that the ic can consume at t a =25c (normal temperature). as the ic consumes power, it heats up, causing its temperature to be higher than the ambient temperature. the allowable temperature that the ic can accept is limited. this depends on the circuit configuration, manufacturing process, and consumable power. power dissipation is determined by the allowable temperature within the ic (maximum junction temperature) and the thermal resistance of the package used (heat dissipation capability). maximum junction temperature is typically equal to the maximum storage temperature. the heat gener ated through the consumption of power by the ic radiates from the mold resin or lead frame of the package. thermal resistance, represented by the symbol ja c/w, indicates this heat dissipation capability. similarly, the temperature of an ic inside its package can be estimated by thermal resistance. figure 102 (a) shows the model of the thermal resistance of a package. the equation below shows how to compute for the thermal resistance ( ja ), given the ambient temperature (t a ), maximum junction temperature (t jmax ), and power dissipation (p d ). ja = (t jmax t a ) / p d c/w the derating curve in figure 102 (b) indicates the power that the ic can consume with reference to ambient temperature. power consumption of the ic begins to attenuate at certai n temperatures. this gradient is determined by thermal resistance ( ja ), which depends on the chip size, power consumpti on, package, ambient temperature, package condition, wind velocity, etc. this may also vary even when the sa me of package is used. thermal reduction curve indicates a reference value measured at a specified condition. figure 102. (c) to (f) show a derating curve for an example of ba10358, ba10324a, ba2904s, ba2904, ba2904w, ba2902s, ba2902. (note 30) (note 31) (note 32) (note 33) (note 34) (note 35) (note 36) (note 37) (note 38) (note 39) (note 40) unit 6.2 5.4 5.0 8.2 7. 0 4.5 6.2 5.0 4. 7 7.0 4.5 mw/c when using the unit above t a =25c, subtract the value above per degree c. permissible dissipation is the value w hen fr4 glass epoxy board 70mm 70mm 1.6mm (copper foil area below 3%) is mounted. 0 200 400 600 800 1000 0 25 50 75 100 125 150 ambient temperature [ ] . power dissipation [mw] . 0 200 400 600 800 1000 0 25 50 75 100 125 150 ambient temperature [ ] . power dissipation [mw] . 0 200 400 600 800 1000 0 25 50 75 100 125 ambient temperature [ ] . power dissipation [mw] . 0 200 400 600 800 1000 0 25 50 75 100 125 a mbi en t te mp era ture [ ] . power dissipation [mw] . (e)ba2904 (f)ba2902 (c)ba10358 ba10358f (n o t e 30 ) ba10358fv (n o t e 32 ) ba10358fj (n o t e 31 ) ba10324afv v (n o t e 34 ) ba10324af (n o t e 35 ) ba10324afj (n o t e 33 ) ba2904f (n o t e 36 ) ba2904wf (note 36) ba2904sf (note 36) ba2904fv (n o t e 37 ) ba2904wfv (note 37) ba2904sfv (note 37) ba2904fvm (n o t e 38 ) ba2904sfvm (note 38) ba2902fv (n o t e 39 ) ba2902sfv (note 39) ba2902f( (n o t e 40 ) ba2902sf (note 40) (d)ba10324 a mbient temperature t a [ c ] chip surface temperature t j [ c ] (a) thermal resistance ja =(t jmax -t a )/ p d c/w 0 50 75 100 125 150 25 p1 p2 pd (max) lsi M [w] ' ja2 ' ja1 tj ' (m ax ) ja2 < ja1 ?? ta [ ] ja2 ja1 tj (m ax ) ambient temperature t a [ ? c] p d(max) ja2 < ja1 ja2 ja2 ja1 ja1 t jmax t jmax power dissipation of ic power dissipation of lsi [w] (b) derating curve downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 41/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx operational notes 1. reverse connection of power supply connecting the power supply in reverse polarity can damage the ic. take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the ics power supply terminals. 2. power supply lines design the pcb layout pattern to provide low impedance ground and supply lines. separate the ground and supply lines of the digital and analog blocks to prevent noise in t he ground and supply lines of the digital block from affecting the analog block. furthermore, connect a capacitor to gr ound at all power supply pins. consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. ground voltage ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. ground wiring pattern when using both small-signal and large- current gnd traces, the two ground trac es should be routed separately but connected to a single ground at the refe rence point of the application board to av oid fluctuations in the small-signal ground caused by large currents. also ens ure that the gnd traces of external components do not cause variations on the gnd voltage. the power supply and ground lines must be as short and thick as possible to reduce line impedance. 5. thermal consideration should by any chance the power dissipation rating be exceeded, the rise in temperature of the chip may result in deterioration of the properties of the ch ip. the absolute maximum rating of the pd stated in this specification is when the ic is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. in case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the pd rating. 6. recommended operating conditions these conditions represent a range within which the expect ed characteristics of the ic can be approximately obtained. the electrical characteristics are guaranteed under the conditions of each parameter. 7. inrush current when power is first supplied to the ic, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the ic has more than one power supply. therefore, give special consideration to power coupling capacitance, power wiring, width of gnd wiring, and routing of connections. 8. operation under strong electromagnetic field operating the ic in the presence of a strong electromagnetic field may cause the ic to malfunction. 9. testing on application boards when testing the ic on an application board, connecting a ca pacitor directly to a low-impedance output pin may subject the ic to stress. always discharge capacitors completely after each process or step. the ics power supply should always be turned off completely before connecting or removi ng it from the test setup duri ng the inspection process. to prevent damage from static discharge, ground the ic durin g assembly and use similar precautions during transport and storage. 10. inter-pin short and mounting errors ensure that the direction and position are correct when mount ing the ic on the pcb. incorrect mounting may result in damaging the ic. avoid nearby pins being shorted to each other especially to ground. inter-pin shorts could be due to many reasons such as metal particles, water droplets (i n very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 42/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx vcc vee v icm - + operational notes C continued 11. regarding input pins of the ic this monolithic ic contains p+ isolation and p substrat e layers between adjacent elements in order to keep them isolated. p-n junctions are formed at the intersection of th e p layers with the n layers of other elements, creating a parasitic diode or transistor. for example (refer to figure below): when gnd > pin a and gnd > pin b, the p-n junction operates as a parasitic diode. when gnd > pin b, the p-n junction operates as a parasitic transistor. parasitic diodes inevitably occur in the structure of the ic. the operation of parasitic diodes can result in mutual interference among circuits, operational faults, or physical damage. therefore, conditions that cause these diodes to operate, such as applying a voltage lower than the gnd voltage to an input pin (and thus to the p substrate) should be avoided. nn p + p nn p + p substrate parasitic element gnd n p + nn p + n p p substrate gnd gnd parasitic element pin a pin a pin b pin b bc e parasitic element gnd parasitic element or transistor parasitic element c be transistor (npn) resistor figure 103. example of monolithic ic structure 12. unused circuits when there are unused circuits it is recommended that they be connected as in figure 104, setting the non-inverting input terminal to a potential within the in-phase input voltage range (v icm ). figure 104. disable circuit example 13. input terminal voltage (ba10358 / ba10324) applying vee + 32v, (ba2904 / ba2902) applying vee + 36v to the input terminal is possible without causing deterioration of the electric al characteristics or destruction, irres pective of the supply voltage. however, this does not ensure normal circuit operatio n. please note that the ci rcuit operates normally only when the input voltage is within the common mode input voltage range of the electric characteristics. 14. power supply (signal / dual) the op-amp operates when the spec ified voltage supplied is between vcc an d vee. therefore, the single supply op-amp can be used as a dual supply op-amp as well. 15. terminal short-circuits when the output and vcc terminals are shorted, excessive output current may flow, resulting in undue heat generation and, subsequently, destruction. 16. ic handling applying mechanical stress to the ic by deflecting or bending the board may cause fluc tuations in the electrical characteristics due to piezo resistance effects. 17. output capacitor if a large capacitor is connected between the output pin and vee pin, current from the charged capacitor will flow into the output pin and may destroy the ic when the vcc pin is shorted to ground or pulled down to 0v. use a capacitor smaller than 0.1uf between output pin and vee pin. keep this potential in v icm downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 43/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx physical dimensions tape and reel information package name sop8 ? order quantity needs to be multiple of the minimum quantity. embossed carrier tape tapequantity direction of feed the direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand 2500pcs e2 () direction of feed reel 1pin (unit : mm) pkg : sop8 drawing no. : ex112-5001-1 (max 5.35 (include.burr)) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 44/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx physical dimension, tape and reel information C continued package name sop-j8 ? order quantity needs to be multiple of the minimum quantity. embossed carrier tape tapequantity direction of feed the direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand 2500pcs e2 () direction of feed reel 1pin downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 45/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx physical dimension, tape and reel information C continued package name ssop-b8 ? order quantity needs to be multiple of the minimum quantity. embossed carrier tape tapequantity direction of feed the direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand 2500pcs e2 () direction of feed reel 1pin downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 46/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx physical dimension, tape and reel information C continued package name msop8 direction of feed reel ? order quantity needs to be multiple of the minimum quantity. embossed carrier tape tapequantity direction of feed the direction is the 1pin of product is at the upper right when you hold reel on the left hand and you pull out the tape on the right hand 3000pcs tr () 1pin downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 47/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx physical dimension, tape and reel information C continued package name sop14 ? order quantity needs to be multiple of the minimum quantity. embossed carrier tape tapequantity direction of feed the direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand 2500pcs e2 () direction of feed reel 1pin (unit : mm) pkg : sop14 drawing no. : ex113-5001 (max 9.05 (include.burr)) downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 48/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx physical dimension, tape and reel information C continued package name sop-j14 ? order quantity needs to be multiple of the minimum quantity. embossed carrier tape tapequantity direction of feed the direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand 2500pcs e2 () direction of feed reel 1pin downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 49/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx physical dimension, tape and reel information C continued package name ssop-b14 ? order quantity needs to be multiple of the minimum quantity. embossed carrier tape tapequantity direction of feed the direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand 2500pcs e2 () direction of feed reel 1pin downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 50/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx marking diagrams sop8(top view) part number marking lot number 1pin mark msop8(top view) part number marking lot number 1pin mark ssop-b8(top view) part number marking lot number 1pin mark sop14(top view) part number marking lot number 1pin mark ssop-b14(top view) part number marking lot number 1pin mark sop-j8(top view) part number marking lot number 1pin mark sop-j14(top view) part number marking lot number 1pin mark downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 51/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx land pattern data all dimensions in mm pkg land pitch e land space mie land length R? 2 land width b2 sop8 1.27 4.60 1.10 0.76 ssop-b8 0.65 4.60 1.20 0.35 sop-j8 1.27 3.90 1.35 0.76 msop8 0.65 2.62 0.99 0.35 sop14 1.27 4.60 1.10 0.76 ssop-b14 0.65 4.60 1.20 0.35 sop-j14 1.27 3.90 1.35 0.76 product name package type marking ba10358 f sop8 10358 fj sop-j8 fv ssop-b8 358 ba10324a f sop14 ba10324af fj sop-j14 ba10324a fv ssop-b14 324a ba2904 f sop8 2904 fv ssop-b8 fvm msop8 ba2904w f sop8 fv ssop-b8 ba2904s f sop8 2904s fv ssop-b8 04s fvm msop8 2904s ba2902 f sop14 ba2902f fv ssop-b14 2902 ba2902s f sop14 2902s fv ssop-b14 b e e ? sop8, ssop-b8, sop-j8, msop8 sop14, ssop-b14, sop-j14 downloaded from: http:///
datasheet www.rohm.com tsz02201-0rar0g200130-1-2 ? 2013 rohm co., ltd. all rights reserved. 52/52 23.jan.2014 rev.003 tsz22111 ? 15 ? 001 ba10358xx, ba10324a xx, ba2904xxx, ba2904sxxx, ba2904wxx ba2902xx , ba2902sxx revision history date revision changes 14.sep.2012 001 new release 11.jan.2013 002 land pattern data inserted. 23.jan.2014 003 the differential input voltage and input common-mode voltage range are updated in absolute maximum ratings for ba10358 and ba10324a. the input current is added in absolute maximum ratings. downloaded from: http:///
datasheet d a t a s h e e t notice - ge rev.002 ? 2014 rohm co., ltd. all rights reserved. notice precaution on using rohm products 1. our products are designed and manufac tured for application in ordinary elec tronic equipments (such as av equipment, oa equipment, telecommunication equipment, home electroni c appliances, amusement equipment, etc.). if you intend to use our products in devices requiring ex tremely high reliability (such as medical equipment (note 1) , transport equipment, traffic equipment, aircraft/spacecra ft, nuclear power controllers, fuel c ontrollers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (specific applications), please consult with the rohm sale s representative in advance. unless otherwise agreed in writing by rohm in advance, rohm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ro hms products for specific applications. (note1) medical equipment classification of the specific applications japan usa eu china class class class b class class class 2. rohm designs and manufactures its products subject to strict quality control system. however, semiconductor products can fail or malfunction at a certain rate. please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe desi gn against the physical injury, damage to any property, which a failure or malfunction of our products may cause. the following are examples of safety measures: [a] installation of protection circuits or other protective devices to improve system safety [b] installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. our products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditio ns, as exemplified below. accordin gly, rohm shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of an y rohms products under any special or extraordinary environments or conditions. if you intend to use our products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] use of our products in any types of liquid, incl uding water, oils, chemicals, and organic solvents [b] use of our products outdoors or in places where the products are exposed to direct sunlight or dust [c] use of our products in places where the products ar e exposed to sea wind or corrosive gases, including cl 2 , h 2 s, nh 3 , so 2 , and no 2 [d] use of our products in places where the products are exposed to static electricity or electromagnetic waves [e] use of our products in proximity to heat-producing components, plastic cords, or other flammable items [f] sealing or coating our products with resin or other coating materials [g] use of our products without cleaning residue of flux (ev en if you use no-clean type fluxes, cleaning residue of flux is recommended); or washing our products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] use of the products in places subject to dew condensation 4. the products are not subjec t to radiation-proof design. 5. please verify and confirm characteristics of the final or mounted products in using the products. 6. in particular, if a transient load (a large amount of load applied in a short per iod of time, such as pulse. is applied, confirmation of performance characteristics after on-boar d mounting is strongly recomm ended. avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading c ondition may negatively affect product performance and reliability. 7. de-rate power dissipation (pd) depending on ambient temper ature (ta). when used in seal ed area, confirm the actual ambient temperature. 8. confirm that operation temperat ure is within the specified range described in the product specification. 9. rohm shall not be in any way responsible or liable for fa ilure induced under deviant condi tion from what is defined in this document. precaution for mounting / circuit board design 1. when a highly active halogenous (chlori ne, bromine, etc.) flux is used, the resi due of flux may negatively affect product performance and reliability. 2. in principle, the reflow soldering method must be used; if flow soldering met hod is preferred, please consult with the rohm representative in advance. for details, please refer to rohm mounting specification downloaded from: http:///
datasheet d a t a s h e e t notice - ge rev.002 ? 2014 rohm co., ltd. all rights reserved. precautions regarding application examples and external circuits 1. if change is made to the constant of an external circuit, pl ease allow a sufficient margin considering variations of the characteristics of the products and external components, including transient characteri stics, as well as static characteristics. 2. you agree that application notes, re ference designs, and associated data and in formation contained in this document are presented only as guidance for products use. theref ore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. rohm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. precaution for electrostatic this product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. please take proper caution in your manufacturing process and storage so that voltage exceeding t he products maximum rating will not be applied to products. please take special care under dry condit ion (e.g. grounding of human body / equipment / solder iron, isolation from charged objects, se tting of ionizer, friction prevention and temperature / humidity control). precaution for storage / transportation 1. product performance and soldered connections may deteriora te if the products are stor ed in the places where: [a] the products are exposed to sea winds or corros ive gases, including cl2, h2s, nh3, so2, and no2 [b] the temperature or humidity exceeds those recommended by rohm [c] the products are exposed to di rect sunshine or condensation [d] the products are exposed to high electrostatic 2. even under rohm recommended storage c ondition, solderability of products out of recommended storage time period may be degraded. it is strongly recommended to confirm sol derability before using products of which storage time is exceeding the recommended storage time period. 3. store / transport cartons in the co rrect direction, which is indicated on a carton with a symbol. otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. use products within the specified time after opening a humidity barrier bag. baking is required before using products of which storage time is exceeding the recommended storage time period. precaution for product label qr code printed on rohm products label is for rohms internal use only. precaution for disposition when disposing products please dispose them proper ly using an authorized industry waste company. precaution for foreign exchange and foreign trade act since our products might fall under cont rolled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with rohm representative in case of export. precaution regarding intellectual property rights 1. all information and data including but not limited to application example contained in this document is for reference only. rohm does not warrant that foregoi ng information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. rohm shall not be in any way responsible or liable for infringement of any intellectual property rights or ot her damages arising from use of such information or data.: 2. no license, expressly or implied, is granted hereby under any intellectual property rights or other rights of rohm or any third parties with respect to the information contained in this document. other precaution 1. this document may not be reprinted or reproduced, in whol e or in part, without prior written consent of rohm. 2. the products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of rohm. 3. in no event shall you use in any wa y whatsoever the products and the related technical information contained in the products or this document for any military purposes, incl uding but not limited to, the development of mass-destruction weapons. 4. the proper names of companies or products described in this document are trademarks or registered trademarks of rohm, its affiliated companies or third parties. downloaded from: http:///
datasheet datasheet notice C we rev.001 ? 2014 rohm co., ltd. all rights reserved. general precaution 1. before you use our pro ducts, you are requested to care fully read this document and fully understand its contents. rohm shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny rohms products against warning, caution or note contained in this document. 2. all information contained in this docume nt is current as of the issuing date and subj ec t to change without any prior notice. before purchasing or using rohms products, please confirm the la test information with a rohm sale s representative. 3. the information contained in this doc ument is provi ded on an as is basis and rohm does not warrant that all information contained in this document is accurate an d/or error-free. rohm shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. downloaded from: http:///

▲Up To Search▲

Price & Availability of BA2904SFVM-TR

	To Download BA2904SFVM-TR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .